Cara Menghubungkan Jaringan Berbeda Menggunakan Router Dengan Cara Routing OSPF Di Packet Tracer

Pertama buat rangaka seperti diatas kabel diantara PC dan Router menggunakan kabel cross-over
dan kabel diantara Router dan Router menggunkan kabel Serial DCE.



Keterangan :

PC0       :Fa0/0 192.168.2.2/27
Router0:Fa0/0 192.168.2.1/27
             :Se2/0 10.200.1.1/30
             :Se3/0 10.100.1.1/30
Router1:Fa0/0 192.168.1.1/27
             :Se2/0 10.200.1.2/27
             :Se3/0 10.150.1.1/30
PC1       :Fa0/0 192.168.1.2/27
Router3:Se3/0 10.150.1.2/30
             :Se2/0 10.100.1.2/30
             :Fa0/0 10.100.10.1/30
             :Fa1/0 192.168.3.1/27
PC2       :Fa0/0 192.168.3.2/27
Router2:Fa0/0 10.100.10.2/30
             :Fa1/0 192.168.4.1/27
PC3       :Fa0/0 192.168.4.2/27

 

Setting IP Router pada CLI seperti ini:
Router 0 : 

Router > enable
Router#conf t
Router(config)#interface serial2/0
Router(config-if)#ip address 10.200.1.1 255.255.255.252
Router(config-if)#no shutdown
Router(config-if)#exit 
Router(config)#interface serial3/0
Router(config-if)#ip address 10.100.1.1 255.255.255.252
Router(config-if)#no shutdown
Router(config-if)#clock rate 9600
Router(config-if)#exit
Router(config)#interface fasethernet 0/0
Router(config-if)#ip address 192.168.2.1 255.255.255.224
Router(config-if)#no shutdown
Router(config-if)#exit

Router 1 :

Router > enable
Router#conf t
Router(config)#interface serial2/0
Router(config-if)#ip address 10.200.1.2 255.255.255.224
Router(config-if)#no shutdown
Router(config-if)#clock rate 9600 
Router(config-if)#exit 

Router(config)#interface serial3/0
Router(config-if)#ip address 10.150.1.1 255.255.255.252
Router(config-if)#no shutdown
Router(config-if)#exit
Router(config)#interface fasethernet 0/0
Router(config-if)#ip address 192.168.1.1 255.255.255.224
Router(config-if)#no shutdown
Router(config-if)#exit


Router 3 :

Router > enable
Router#conf t
Router(config)#interface serial2/0
Router(config-if)#ip address 10.100.1.2 255.255.255.252
Router(config-if)#no shutdown
Router(config-if)#exit 

Router(config)#interface serial3/0
Router(config-if)#ip address 10.150.1.2 255.255.255.252
Router(config-if)#no shutdown
Router(config-if)#clock rate 9600
Router(config-if)#exit
Router(config)#interface fasethernet 0/0
Router(config-if)#ip address 10.100.10.1 255.255.255.252
Router(config-if)#no shutdown
Router(config-if)#exit
Router(config)#interface fasethernet 1/0
Router(config-if)#ip address 192.168.3.1 255.255.255.224
Router(config-if)#no shutdown
Router(config-if)#exit 


Router 2 :

Router > enable
Router#conf t
Router(config)#interface fasethernet1/0
Router(config-if)#ip address 192.168.4.1 255.255.255.224
Router(config-if)#no shutdown
Router(config-if)#exit
Router(config)#interface fasethernet0/0
Router(config-if)#ip address 10.100.10.2 255.255.255.252
Router(config-if)#no shutdown
Router(config-if)#clock rate 9600
Router(config-if)#exit

Lalu Setting Router OSPF-nya:
Router 0:
Router>enable
Router#conf t
Router(config)#router ospf 1
Router(config-router)#network 192.168.2.0 0.0.0.255 area 0
Router(config-router)#network 10.100.1.0 0.255.255.255 area 0
Router(config-router)#network 10.200.1.0 0.255.255.255 area 0
Router 1:
Router>enable

Router#conf t

Router(config)#router ospf 1
Router(config-router)#network 192.168.1.0 0.0.0.255 area 0
Router(config-router)#network 10.200.1.0 0.255.255.255 area 0
Router(config-router)#network 10.150.1.0 0.255.255.255 area 0
Router 3:
Router>enable

Router#conf t

Router(config)#router ospf 1
Router(config-router)#network 192.168.3.0 0.0.0.255 area 0
Router(config-router)#network 10.100.1.0 0.255.255.255 area 0
Router(config-router)#network 10.100.10.0 0.255.255.255 area 0
Router(config-router)#network 10.150.1.0 0.255.255.255 area 0
 Router 2:
Router>enable

Router#conf t

Router(config)#router ospf 1
Router(config-router)#network 192.168.4.0 0.0.0.255 area 0
Router(config-router)#network 10.100.10.0 0.255.255.255 area 0

nb:router ospf 1 => Untuk Menerangkan Golongan OSPF-nya ospf 1 nya bisa di ganti
                                OSPF 2,OSPF 3 dsb.
     area 0            =>Untuk Menerangkan AREA OSPF-nya AREA-nya juga bisa diganti.

Lalu coba kirimkan filenya dan hasilnya succesfull.

Lalu coba Ping PC0 ke PC1 dan hasilnya reply.












http://ultima-maximus.blogspot.com/2011/10/cara-menghubungkan-jaringan-berbeda.html